SERVICE MANUAL AIR CONDITIONER Air conditioner Portable MODEL: EXP09CN1W EXP09HN1W EXP12HL1W Electrolux Home Products Italy S.p.A. Corso Li
7 (6) Timer button Used to initiate the AUTO ON start time and AUTO OFF stop time program, in conjuction with the (+)&(-) buttons. The t
8 3. Dimension Unit Dimension W(mm) H(mm) D(mm) Single-hole 467 765 397
9 4 Refrigerant Cycle Diagram The figure below is a brief description of the important components and their function in what is called the refrig
10 (2).This figure below is fit for Heat Pump Unit. LIQUID SIDEGAS SIDEHEATEXCHANGE(EVAPORATOR)HEATEXCHANGE(CONDENSER)COMPRESSORCHECK VALV
11 5 Wiring Diagram EXP09CN1W2,EXP09CN1W5 202025490744
12 EXP09HN1WI, EXP12HN1WI,EXP09HN1W5, 202025490732
13 6 Electronic function 6.1 Terms and definitions TC: Temperature of evaporator (T2). TA: Temperature of indoor ambient (T1). TS: The set tem
14 6.5.2.1 If TA﹥TS+1℃, the outdoor fan operates. After 15 seconds, the compressor operates. 6.5.2.2 The compressor is on, if TA≤T
15 6.6.3. The ION/TIMER functions are valid at the drying mode. 6.7 Heating mode 6.7.1. The speed of indoor fan can be optionally chosen as High/
16 6.9 Some standard functions synopsis 6.9.1. Timer function When the unit is on, press the Timer button will initiate the Auto-off stop progr
17 7 Installation details 7.1 Installation instructions The air conditioner should be placed on a firm foundation to minimize noise and vib
18 Note: If the window opening is less than the mentioned minimum length of the window slider kit, cut that one with a hole in it short
19 A a B b Type I 67.5 2.22 123 4.04 Type II 56.2 1.84 98.2 3.22 1. Cut the foam seal (adhesive type) to the proper length and
20 C Type I 26.5"~48.0" Type II 22.1"~38.6" 3. Cut the foam seal (adhesive type) to the proper length and attach it on the
21 2. Attach the window slider kit to the window stool. Adjust the length of the window slider kit according to the width of window. Short
22 4. Close the sliding sash securely against the window. 5. Cut the foam seal to an appropriate length and sealing the o
23 previous pages for window kit installation. 2. Insert the hook of the Exhaust hose into the hole seat of the air outlet and slide down the
24 Note: Cover the hole using the adaptor cap when not in use. The duct can be compressed or extended moderately according to the installation req
25 drain connector, just attach the drain hose to the hole. Place the open end of the hose directly over the drain area in your basement floor. Plea
26 -When the water level of the bottom tray reaches a predetermined level, the unit beeps 8 times, the digital display area sho
CONTENTS 1. Precaution ...
27 3. Unit idle for a long time ※Remove the rubber plug at the back of the unit and attach a hose to drain outlet. Place the open end o
28 8 Basic test procedure 8.1 Defective compressor Compressors are single phase, depending on the model unit. All compressor motors are perm
29 The reason for compressor inefficiency is normally due to broken or damaged suction and/or discharge valves, reducing the ability of the compress
30 connected in series with the common motor terminal. Should the internal temperature and/or current draw become excessive; the contacts in the ove
31 8.2.3 Hermetic compressor replacement. The following procedure applies when replacing components in the sealed refrigeration circuit or repairing
32 1. Recover all refrigerant and oil from the system. 2. Remove compressor, capillary tube and filter drier from the system. 3. Flush evaporator co
33 1. Determine that capacitor is serviceable. 2. Disconnect fan motor wires from fan speed switch or system switch. 3. Apply "live" test
34 and then gradually move back to infinity. 4. Reverse the leads of the probe and momentarily touch the capacitor terminals. The deflection of the
35 10 Troubleshooting In general, possible trouble is classified in three kinds. One is called Starting Failure which is caused from an electrica
36 PPD_121107_A(50Hz, 60Hz)
1 1. Precaution 1.1 Safety Precaution. To prevent injury to the user or other people and property damage, the following instructions must b
2 It may cause injury, accident, or damage to the product. Be sure the installation area does not deteriorate with age. If the base collapses, th
3 unit is so equipped.) There is risk of physical injury, electric shock, or product failure. When the product is soaked (flooded or submerged),
4 Operational. Do not expose the skin directly to cool air for long periods of time. (Do not sit in the draft). This could harm to your he
5 2. Function and control panel 2.1 Function ※ Operation mode: Cooling, Heating, Dry, Fan and Auto. ※ ION (optional) ※ Auto swing function.
6 (1) POWER button Power switch on/off (2) SLEEP button Used to initiate the SLEEP operation. (3) FAN/ION button (ION is optional) Control the f
Comments to this Manuals