Electrolux ENL60810X User Manual download pdf (Page 6)

6 electrolux side by side refrigeration user manual

When correctly installed, your refrigerator should:

• have adequate clearance to the back, sides and top

for air circulation.

• be aligned to the surrounding cupboards

• have doors that will self close from a partially open position

Compact Side by Side 610L

898mm

1754mm

1736mm

18mm

754mm

736mm

8mm

890mm

1115mm

718mm

600mm

90mm

90°

Side by Side 700L

1000mm

1754mm

1736mm

18mm

1000mm

4mm

6mm

992mm

1206mm

718mm

600mm

90mm

90°

caution

Automatic aerosol systems (such as insect conrtol) should not be

located adjacent to the product as the spray may cause long term

damage to the external plastics of the appliance.

Clearances around your refrigerator

Your Side by Side Refrigerator can be installed between

cupboards or xtures but you must allow for the following spaces

around the cabinet.

• allow a minimum of 5 millimetres clearance on both sides (refer

to diagram 1).

• allow a minimum of 10 millimetres clearance above hinge

covers (refer to diagram 1).

• allow a minimum of 50 millimetres at the back of the

refrigerator (refer to diagram 1).

898mm

17 m

17 mm

1 mm

28mm

10mm

90°

50mm

5mm

Recommended

airspace

CABINET

DOORS

Diagram 1

• allow a 200 or 350 millimetres clearance on the hinge side of the

doors, if you place the refrigerator next to

the wall. This will make cleaning easier (refer to diagram 2).

• make sure that cupboards or xtures do not stick out further than

the refrigerator cabinet.

Freezer

Door

Fridge

Door

200mm

350mm

CABINE

Installation

The refrigerator should arrive with the

front rollers wound down.

We recommend that the refrigerator

be tilted backwards by about 10

to 15 millimetres, this will allow

the doors to self close providing

a consistent door seal. To do this

follow the instructions below.

When you want to install your

refrigerator, take the

following steps.

1. Roll the refrigerator into it’s nal position.

warning

The rollers are designed for forward or backward

movement only. They are not castors. Moving the

refrigerator sideways may damage your ﬂoor and the

rollers.

2. If the refrigerator is not tilted back you can adjust the two front

rollers by adjusting the large plastic roller nut (refer page 7).

You may need two people, one to adjust rollers and one to tilt

the refrigerator slightly back to take the weight of the appliance

off the front rollers.

This will increase or decrease the height of the rollers. One

turn of the nut will change the tilt of the refrigerator by

approximately 10mm.

3. If the cabinet is level, then the side walls should be plumb

or vertical. If the cabinet is built in or partly built in check the

alignment of the cabinet side against the cupboard.

aligned to cupboard –

even gap

Top of refrigerator

is level – horizontal

Adjust front rollers for

unevenness of floor.

eg. adjust this roller down.

Packing may be required

underneath the rear roller

to ensure stability.

4. If the appliance now rocks from one corner to the opposite

rear corner, this means that the oor is uneven; you will need

to put some packing under one of the rear rollers.

5. You may now need to ne-tune the installation by adjusting the

front rollers once again.

General Installation

10-15mm

Fixed rear

rollers

Height adjustable

front rollers

Note: Doors are designed

to sit proud of cabinetry

(not ﬂush). The clearances

shown above are the

recommended minimum

clearances.

Diagram 2

1 2 3 4 5 6 7 8 9 10 11 ... 83 84

Comments to this Manuals

No comments

Electrolux ENL60810X User Manual Page 6

Comments to this Manuals

Related products and manuals for Fridges Electrolux ENL60810X