Electrolux EFME627UTT Specifications Sheet download pdf (Page 3)

High standards of quality at Electrolux Home Products, Inc.

mean we are constantly working to improve our products.

We reserve the right to change specifications or

discontinue models without notice.

Electrolux Major Appliances, N.A.

USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-877-4electrolux (1-877-435-3287) • electroluxappliances.com

CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxappliances.ca

RearRear

Front Load Electric Dryers -

EFME417S_EFME517S_EFME617S (steam)

Electrolux

/2"

240V

Power

supply

/4"

Water inlet

/2"

/16"

" hose

clearance

required

Wall

38"

(75

/4"

min.

for stacked

units)

Reversible

Door Swing

27"

Front

15"

Pedestal Drawer

Installation

Elevates dryer height to 53

/4".

For detailed pedestal installation,

refer to instructions included

with pedestal or on web.

Pedestal Installation may require

modified utility hookup locations.

For details, refer to Product

Installation Guide on web.

Installation Clearances:

Dryer can be built in alone or with washer

(side by side or stacked) in closet, recess or

under counter installation with 0"

minimum

clearance required around sides and back of

unit(s).

To achieve 0"

minimum rear clearance,

dryer MUST be vented straight back or with

quick-turn 90° elbow. Steam dryer requires

additional 3/4" steam hose clearance at back of

unit(s). Installation of closet door(s) requires

additional 1"

minimum clearance between front

of unit(s) and door(s). Location of plumbing,

exhaust and utility hookups MUST be considered

when planning any built-in installation. For

additional installation details, refer to Product

Installation Guides on web.

Under Counter Installation:

Installation of dryer alone or side by side

with washer under counter, requires custom-built

countertop and/or cabinetry to accommodate

unit(s) height.

Stacking Units:

Stacking dryer above washer requires use of

optional Stacking Kit (PN# STACKIT7X) with

modified utility hookup locations for dryer. For

complete installation details, refer to instructions

included with Stacking Kit or on web.

Vented door

Closet Installation:

If washer and dryer are installed in same closet, door(s)

MUST be vented with 120 sq.

in. minimum louvered

opening, equally divided, located 3" from top and bottom

of door. Louvered door(s) with equivalent air openings for

full-length of door is acceptable. Air openings MUST

remain unobstructed with door(s) installed.

Built-In Installations

Side

0"min. 0"min. 0"min.* 1" min.

Front

*Steam dryer requires additional 3/4" hose clearance.

/2"

Overall depth with drawer

fully extended – 42

/2"

/4"

Side

27"

15"

Front

Left

/8"

/2"

•

Do NOT install in area exposed to dripping water or outdoor weather conditions,

or where gasoline or other flammables, including automobiles, are kept or stored.

•

For garage installation, dryer MUST be located minimum 18" above floor.

•

Floor MUST be solid with 1" maximum slope. To ensure vibration or movement

does not occur, reinforcement of floor may be necessary. Do NOT install on

carpeted surface.

•

Dryer MUST exhaust to outside of building, NOT into any concealed space.

•

Dryer equipped for 4-way venting and approved for up to 125-foot-equivalent

of duct length, determined by length of run and number of elbows needed.

•

Exhaust installation requires minimum 4"-diameter rigid or semi-rigid metal duct

with approved, unobstructed vent hood having swing-out damper(s). If installing

rigid metal duct (preferred), do not exceed MAXIMUM venting run length of 125 ft.,

allow deductions for elbows and vents. If installing semi-rigid metal duct, do not

exceed MAXIMUM venting run length of 8 ft., always allow deductions for elbows

and vents (Refer to Product Installation Guide on web for additional information).

Do NOT use flexible plastic or metal foil duct and use shortest run possible.

•

Leveling legs supplied to level dryer properly and reduce excessive noise and

vibration.

•

Water inlet hose for steam setting connects to cold water supply with “Y”

connector and requires 3/4" clearance between back of unit and wall.

Note: For planning purposes only. Refer to Product Installation Guide

on the web at electroluxappliances.com for detailed instructions.

Optional Accessories

•

Pedestal Drawers – Titanium (PN #

EPWD257U

TT), Island White (PN #

EPWD257U

IW).

•

Dryer Stacking Kit – (PN # STACKIT7X).

•

Drying Rack – (PN # A04840701).

Electric Dryer Specifications

•

Product Weight – 130 Lbs. / Shipping Weight – 140 Lbs.

•

Voltage Rating – 240 / 60 Hz / 30A

•

Single phase 3- or 4-wire cable, 240 Volt, 60 Hertz AC only electrical

supply with ground required on separate circuit fused on both sides of line.

(Do not use same circuit as washer.)

•

Connected Load (kW Rating) @ 240 Volts = 6.0 kW

•

Amps @ 240V = 25A

•

Dryer MUST employ a 3-conductor NEMA 10-30 type SRDT or 4-conductor

NEMA 14-30 type SRDT or ST (as required), rated at 240 volt AC minimum,

30 amp power supply cord marked for use with clothes dryers (not supplied).

•

Grounding through neutral link prohibited in specific applications and certain

locales, requiring use of 4-wire system. (For detailed electrical requirements,

refer to Product Installation Guide on web.)

•

Always consult local and national electric & plumbing codes.

•

Can be installed alone, with or without optional 15" pedestal drawer, or

stacked above matching Electrolux Washer, which requires installation of

optional dryer stacking kit. (For installation details, refer to instructions

included with optional pedestal or stacking kit or on web.)

•

Can be built in alone or with matching Electrolux Washer (side by side or stacked)

in closet, recess or under counter installation with 0" minimum clearance

required around sides and back of unit(s). To achieve 0" minimum rear clearance,

dryer MUST be vented straight back or with quick-turn 90° elbow. Steam dryer

requires additional 3/4" steam hose clearance at back of unit(s). Installation

of closet door(s) requires additional 1" minimum clearance between front of

unit(s) and door(s). Location of plumbing, exhaust and utility hookups MUST be

considered when planning any built-in installation.

•

Under-counter installation requires custom-built countertop and/or cabinetry

to accommodate unit(s) height.

ELECTRIC FRONT LOAD DRYERS

EFME627U TT / IW

1 2 3

Comments to this Manuals

No comments

Electrolux EFME627UTT Specifications Sheet Page 3

Comments to this Manuals

Related products and manuals for Tumble dryers Electrolux EFME627UTT