Electrolux ZA2 User Manual download pdf (Page 7)

English 5

Vacuum programs

Trilobite has three vacuum programs:

“Normal” Trilobite first plots the room by following the walls (edge

cleaning) and then vacuums all open surfaces.

“Quick” The same as Normal, however without egde cleaning.

“Spot” Trilobite vacuums an area of about one square metre twice.

Refer to page 11 for more information on how to proceed and when to

use the different programs.

Starting vacuuming

You will probably use the Normal program most of the time. In Normal

mode,Trilobite starts with approaching a wall and then follows the outer

edges of the room by left turns until one full circumference of the room

is covered. Depending on the size and layout of the room, edge cleaning

may last for up to 15 minutes (25 minutes if it has found the charger).

After this, edge cleaning ends, and vacuuming commences.

Programmable Timer

Trilobite can be programmed to clean at a particular time, on the day

or days you select for cleaning. (Read more on page 12.)

Main cleaning program

During the main cleaning sequence,Trilobite moves freely all over the

room.Trilobite “sees” its way around with the help of harmless ultra-

sound.This is the same technique that is used by bats for navigation in

the dark, for instance, and for foetal diagnosis in hospitals.

When it discovers an object in its path,Trilobite stops a few centimetres

in front of it and then changes direction.Trilobite can handle most

obstacles. However, if it gets stuck, it will continue with its cleaning

program if you release it within 20 minutes, put it back down on the

floor within 30 seconds and press the “Continue Cleaning” button.

If Trilobite is lifted while cleaning, the cleaning program is cancelled

and Trilobite is reset. If this happens, restart Trilobite.To pause a clea-

ning program, press stop. Press to resume.

Charging

If Trilobite is started from the charger or locates it during edge cleaning,

it will return to the charger unit whenever the battery charge falls below

a specific level. Once the batteries have been charged,Trilobite goes to

work again until the room has been vacuumed.When the work is done,

Trilobite returns to the charger. If Trilobite cannot find the charger

during edge cleaning and the battery voltage becomes too low, it will

stop somewhere in the room.

If you use the “Quick” program, always start Trilobite from the char-

ger. It will then return to the charger when it has finished cleaning.

Emptying the dust collector

Empty the dust collector when the dust collector icon shows in the

display. Be sure to empty the dust collector even if it is not completely

full.The light indicator may be due to e.g. a blocked filter.Always

replace the filter with a new one.

Functional Description

Charger

Place the charger close to a wall.

This way, Trilobite will find the

charger in the edge cleaning mode.

Start

Start Trilobite directly from the

charger or face it towards a wall at

a distance of 0.5 m, to the right of

the charger. Start vacuuming

(see page 11).

Edge cleaning

Trilobite starts by first travelling

along the walls of the room to

establish the size of the room.

Cleaning

In the Vacuum Cycle, Trilobite

moves through the room at its own.

To make it easier

to find the charger,

start Trilobite towards

a wall close to and

to the right of the

charger.

To make it possible

for Trilobite to find

its way back to the

charger, place the

charger against

one of the outer

walls of the room.

1 2 3 4 5 6 7 8 9 10 11 12 ... 21 22

Comments to this Manuals

No comments

Electrolux ZA2 User Manual Page 7

Comments to this Manuals

Related products and manuals for Unknown Electrolux ZA2