Electrolux ER2620C User Manual download pdf (Page 7)

Defrosting

The refrigerator automatically defrosts every time the

compressor stops. The water is discharged, via the

pipe, into a tray located at the back of the appliance

above the compressor, where it evaporates.

Important

To avoid defrost water overflowing into the fridge,

periodically clean the water discharge hole in the centre

of the V shaped drip collector at the back of the

refrigerator compartment behind the fruit and vegetable

drawer. Use the defrost cleaner provided which you will

find already inserted into the discharge hole.

Remember to wash the defrost cleaner in hot soapy

water at regular intervals. Dry throughly before

replacing.

D037

MAINTENANCE AND CLEANING

External cleaning

Many proprietary kitchen surface cleaners

contain chemicals that can attack/damage the

plastics used in this appliance. For this reason it

is recommended that the outer casing of this

appliance is only cleaned with warm water with a

little washing-up liquid added.

An accumulation of dust will affect the performance

of the appliance and cause excessive electricity

consumption.

You MUST ensure that the appliance is switched

OFF.

Once or twice a year dust the condenser (black grill)

and the compressor at the back of the appliance,

with a brush or vacuum cleaner, see diagram.

PR259

Before any maintenance or cleaning work is carried

out, DISCONNECT the appliance from the

ELECTRICITY supply.

Internal cleaning

Clean the inside and accessories with warm water

and bicarbonate of soda (5ml to 0.5 litre of water).

Rinse and dry thoroughly.

NEVER USE DETERGENTS, ABRASIVE

POWDERS, HIGHLY PERFUMED CLEANING

PRODUCTS OR WAX POLISHES, TO CLEAN

THE INTERIOR AS THESE WILL DAMAGE THE

SURFACE AND LEAVE A STRONG ODOUR.

Clean the drain hole of the water trough at regular

intervals and make sure that the drain hole is never

obstructed, so that the defrost water may flow freely.

Changing the light bulb

Should the interior light fail to work, first switch off

the appliance and disconnect from the electricity

supply, then replace the bulb as follows;

Unscrew the light cover and then pull it outward by

pressing as shown in the figure. Unscrew the bulb

and replace it with a new 15 watt bulb (available

from your nearest Electrolux Service Force Centre).

Replace the light cover by sliding it into its original

position and replacing the screw.

D411

When the appliance is not in use

When the appliance is not in use for long periods,

disconnect from the electricity supply, empty all

foods and clean the appliance, leaving the doors ajar

to prevent unpleasant smells.

INSTALLATION

Positioning

This appliance should only be installed at a location

where the ambient temperature corresponds to the

climate classification indicated on the rating plate, which

is located at the left on the inside of the appliance.

The following table shows which ambient temperature is

correct for each climate classification:

SN +10°C to + 32°C

N +16°C to + 32°C

ST +18°C to + 38°C

T +18°C to + 43°C

It should be located in a dry atmosphere, out of direct

sunlight and away from extreme temperature e.g. not next

to a boiler or radiator, or in a very cold room e.g. an

outhouse, where the temperatures may fall below 10°C

(50°F). If these temperatures are exceeded i.e. colder or

warmer, then the appliance may not operate correctly.

You should also ensure that air can circulate freely around

the back and the top of the cabinet. There must also be at

least 100 mm (4”) distance between the top of the cabinet

and any overhanging kitchen furniture (A). Ideally, the

appliance should not be positioned beneath overhanging

furniture (B).

There should also be a gap of 25 mm either side of the

appliance. Do not obstruct the space underneath. The

back of the cabinet may be placed close to the wall but

must not touch it. DO NOT install in places with restricted

ventilation.

Adjust the level of the appliance by screwing out the

adjustable foot, or feet, at the bottom of the cabinet using

your fingers or a spanner (see figure).

D200

100 mm10 mm

10 mm

NP007

Warning

IF YOU ARE DISCARDING AN OLD APPLIANCE

THAT HAS A LOCK OR CATCH ON THE DOOR,

YOU MUST ENSURE THAT IT IS MADE

UNUSABLE TO PREVENT YOUNG CHILDREN

BEING TRAPPED INSIDE.

Depending upon the position which you choose for

your appliance, you may wish to reverse the way in

which the door opens. To do this, refer to instructions

on “Door reversal directions”.

Important

It must be possible to disconnect the appliance from

the mains power supply; the plug must therefore be

easily accessible after installation.

Rear spacers

The plastic bag containing all relevant

documentation also contains two spacers to be fitted

into special holes in the back of the appliance.

Fit the spacers into the holes, taking care to ensure

that the arrow (A) is positioned as shown in the

diagram. Then turn them through 45° (arrow (A)

vertical) until they lock into place.

PR60

45°

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Electrolux ER2620C User Manual Page 7

Comments to this Manuals

Related products and manuals for Fridges Electrolux ER2620C