Electrolux Full Size Tumble Action Washer User Manual download pdf (Page 3)

NOTE:

Drain hose attached to the washer can reach a 58

in. (147 cm) high standpipe. For higher standpipe

use hose P/N 131461201, available from an

authorized parts distributor. If drain is less than

24 in. (61 cm), install a siphon break kit, available

at your local hardware store.

Models equipped with gravity drain:

1. Floor drain MUST be capable of eliminating 17

gals (64.3 L) per minute.

2. Floor drain diameter must be at least 1/2 inch larger

than drain hose.

Max.Max.

Max.

PRE-INSTALLATION REQUIREMENTS

Tools Required for Installation:

1. 1/4 in. nut driver

2. 3/8 in. socket with ratchet.

3. 3/8 in. open end wrench.

4. 7/16 in. socket with ratchet.

5. 9/16 in. open end wrench.

6. Channel-lock adjustable pliers.

7. Carpenter’s level.

ELECTRICAL REQUIREMENTS

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY - 2 wire, with ground, 120 volt, single

phase, 60 Hz, Alternating Current. NOTE: The use of

this washer with power created by gas powered

generators, solar powered generators, wind powered

generators or and other generator other than the local

utility company is not recommended.

OUTLET RECEPTACLE - Properly grounded 3-prong

receptacle to be located so the power supply cord is

accessible when the washer is in an installed position.

NOTE: GFI (Ground Fault Interrupter) receptacle is not

required.

GROUNDING REQUIREMENTS

Improper connection of the equipment

grounding conductor can result in a risk of electrical shock.

Check with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

1. The washer MUST be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electrical shock by a path of least resistance

for electrical current.

2. Since your washer is equipped with a power supply

cord having an equipment-grounding conductor and a

grounding plug, the plug MUST be plugged into an

appropriate, copper wired receptacle that is properly

installed and grounded in accordance with all local

codes and ordinances or in the absence of local codes,

with the National Electrical Codes, ANSI/NFPA 70

(latest edition). If in doubt, call a licensed electrician.

DO NOT cut off or alter the grounding prong on the

power supply cord. In situations where a two-slot

receptacle is present, it is the owner’s responsibility

to have a licensed electrician replace it with a

properly grounded three prong grounding type

receptacle.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within

42 inches (107 cm) of your washer’s water inlet. The

faucets MUST be 3/4 inch (1.9 cm) garden hose type

so inlet hoses can be connected. Water pressure MUST

be between 10 and 120 pounds per square inch

(maximum unbalance pressure, hot vs. cold, 10 psi.)

Your water department can advise you of your water

pressure. The hot water temperature should be about

140 degrees F (60 degrees C).

DRAIN REQUIREMENTS

Models equipped with drain pump:

1. Drain MUST be capable of eliminating 17 gals (64.3

L) per minute.

2. A standpipe diameter of 1-1/4 in. (3.18 cm)

minimum.

3. The standpipe height above the floor should be:

1 2 3 4 5 6 7 8 ... 11 12

Comments to this Manuals

No comments

Electrolux Full Size Tumble Action Washer User Manual Page 3

Comments to this Manuals

Related products and manuals for Unknown Electrolux Full Size Tumble Action Washer