Electrolux T4650 Installation Manual

Installation manualT4290, T4530, T4650Selecta Control487 05 44 61/EN 08.38

Technical data10Technical data, T4650Heating Electric Steam GasDrum volume: 650 litres 650 litres 650 litresWeight: Net 340 kg 345 kg 325 kg

Setup11Setup T4290, T4530UnpackingWhen unpacking the machine, handle it with care. There are no transport clamps.PositioningFig. 1 Position the tumble

Setup12Setup T4650UnpackingWhen unpacking the machine, handle it with care. There are no transportation brackets to remove.Fig. 1 From factory the dry

Setup13Setup T4650PositioningFig. 1 Position the tumble dryer so that there is plenty of room for working, both for the user and for the service techn

Door14Reversing the doorThe dryer is usually delivered with a right hinged door but the door can be changed to left hinged position, as illustrated be

Door15Continued8. In order to prevent false air to enter, attatch the sealing strip around the drum casing edge on the same side as the door is to be

Ship installation16Ship installation161000100070670645454545Type 4290 / 309049041067 = Type 4530 / 501067 = Type 4530 / 504545 4545Type 4530 / 50Type

Evacuation system171Evacuation systemAir principleFig. 1 The blower creates low pressure in the dryer, drawing air into the cylinder via the heating u

Evacuation system18Evacuation systemFresh-airFor maximum efficiency and the shortest possible drying time, it is important to ensure that fresh air is

Evacuation system19 1 2 3 4 5 6 7 8 9 10 200 280 315 355 400 450 475 500 535 560 0.15 0.30 0.45 0.60 0.75 0.90 1.05 1.20 1.35 1.50No. of dryersExhaust

Evacuation system201Several dryers on a shared exhaust duct2Evacuation systemGentle bends

Evacuation system21Evacuation systemNonreturn flapIn order to achieve the best result it is important that the dryer has the right volume of air to wo

Installation22Steam installationBefore startThe steam pipe must be cut off and must not be under pressure.SteamSteam 3-10 bar absolute pressure (130-

Installation23Mount a shut-off valve upstream from the dryer.The gas connection to the dryer should be dimensioned to an output depending on the kW-ra

Installation24Before installing the dryer affix the label "Read the user instructions" to the inside of the door, see pictures below.The lab

Installation25Gas group Injector size Ø mm (1)Air reducing plate (fi g. 5)Inlet pres-sure (mbar)Injector pressure (mbar)Label no. (fi g. 10 )I2H, I2E(LL

Installation26Gas group Injector size Ø mm (1)Air reducing plate (fi g. 9)Inlet pres-sure (mbar)Injector pressure (mbar)Label no. (fi g. 10)I2H, I2E(LL

Installation27Conversion instructions - T4290 only: 1. Disconnect the power to the dryer. 2. Open the operating panel. 3. Remove nozzle (1),

Installation28Conversion instructions - T4530 only: 1. Disconnect the power to the dryer. 2. Open the operating panel. 3. Remove nozzle (1),

Installation29Conversion instructions - T4650 only: 1. Disconnect the power to the dryer. 2. Open the operating panel. 3. Remove nozzle 1, se

3ContentsContentsSafety precautions ...5 Dimension sketch ...

Installation30When the dryer is to be converted to another gas type, the data label on the rear of the dryer must be updated in order for the data to

Installation31Electric installationTo be carried out by qualified personnelThe tumble dryer must be connected to its own fuse group and multi-pole mai

Installation32Electric installationConnecting the cable (outside the EU and EEA)1. Demount cover plate A, fig. 1.2. Pass the feeder cable through ca

Installation33Electric installation - electric, gas, steam heatedThe tumble dryer must be connected to its own fuse group and pulti-pole main switch a

Installation34465L1L2L3N1.25 A externalcontrol onlyContinuedFig. 4 Gas and steam heated 3-phase with supply disconnectorFig. 5 Electric heated 3-ph

Installation35Electric installation - optionsExternal connection - 100 mAA special connection terminal is located on the connection console fig. 1.Thi

Installation36SteamElectricElectric installation - T4290Fuse sizes, effects and voltagesVoltageHeat effect kWMotor effectkWMax. effectkWFuseGas230-240

Installation37230-240V 3AC 50/60 Hz 40 kW 1.5 kW 1.5 kW 10A230-240V 1AC 50/60Hz 40 kW 1.5 KW 1.5 kW 10A400-415V 3AC 50/60Hz 40 kW 1.5 kW

Installation38230-240V 3AC 50/60 Hz 57 kW 2 kW 2 kW 10A400-415V 3AC 50/60Hz 57 kW 2 kW 2 kW 10A440-480V 3AC 60HZ 57 kW 2 kW 2 kW 10A230

Function check392To be carried out by qualified personnelFunction checkCheck whether the drum is empty and the door has been closed.Start the dryerChe

Fresh-air intake40Option: Adaptor for direct fresh-air intake - dimension sketchGas- and electric heated dryers 1 Adaptor: T4290 no. 988 80 20 41

www.electrolux.com/laundrysystemsShare more of our thinking at www.electrolux.com

5Safety PrecautionsSafety PrecautionsDo not dry unwashed items in the machineThe machine is not to be used if industrial chemicals have been used for

Technical data7Dimension sketch T4290, T4530, T4650Electric and gas heatingSteam heatingGLHFHACBDEJMOPN56433IIK127 A B C D E F G H I J K L M N O P

Technical data8Technical data, T4290Heating Electric Steam GasDrum volume: 286 litres 286 litres 286 litresWeight: Net 220 kg 220 kg 220 kg

Technical data9Technical data, T4530Heating Electric Steam GasDrum volume: 528 litres 528 litres 528 litresWeight: Net 300 kg 340 kg 300 kg