Electrolux FSF 650 Specifications download pdf (Page 11)

FSF-ed5006

FSF

5. Use of the control

board

The microprocessor programmer manages the pressing cycle in all of

its functions. The user can pre-set 9 pressing programs.

The control panel is subdivided into 4 sections:

• PROGRAMMING:allowsstorageof9differentworkprograms

with programmable times and modes.

• EXCLUSION:allowspartialortotalexclusionofvariouspress-

ing functions.

• MODE:permitschoiceofvariouspressingcyclemodes

• MANUALCONTROLS:allowsmanualfunctionofmainpress-

ing functions.

When the machine is switched on the control panel shows the last

program used.

It is possible to adjust the brightness of the display: press

increase, press

to decrease.

5.1. PROGRAMMING section - basic fea-

tures

The programming section consists of:

• Programnumberdisplay:from1to9

• STEAMtimedisplay:from00to99seconds

• MIX/PAUSEtimedisplay.Thetwo-figuredisplayissharedby

the two functions MIX (mixed steam + air) and PAUSE (pause

betweensteamandblowing;usede.g.fortouchups)

• AIRtimedisplay:blowingtime

• 5programmingbuttons.

To program a pressing cycle, do as follows:

1. Press the button PROG (

) on the panel. A letter “P” ap-

pears in the PROG display and the STEAM time display begins

to flash.

1. Press buttons

or to increase or reduce the steam time.

2. Press the PROG. button (

) to memorize the steam time.

3. The green light MIX and the display below begin to flash: press

or to set a time of mixed steam + air after steaming, if

needed.

4. Press the PROG. button to memorize the mix time

5. The green light PAUSE and the display below begin to flash:

press

or to set a pause time between steam and blowing,

if needed (e.g. for touch ups with the iron)

6. Press the PROG. button to memorize the pause time.

7. The AIR indicator starts to flash. Press

or to set blowing

time.

8. Press the PROG. button. The display stops to flash. Program-

ming is finished

If you need to change only one of the times, repeat all steps without

modifying the other times.

Mix and Pause times can be used or not, depending on the needs.

Table 5.1 shows the possible combinations.

5.2. PROGRAMMING section - advanced

features

The PROGRAMMING sections allows adjustment of several param-

eters. Refer to Table 5.2 for description of the parameters and their

status. Figure 5.3 shows the look of the displays during programming

of advanced parameters.

1. To access advanced programming press the PROG. button until

the letter H appears in the program number display

2. The steam time display shows the number of the parameter

under programming. Press PROG. to step forward to another

parameter

3. The air time display shows a flashing number indicating the

parameter value. Press

or to change parameter value

4. Press PROG. to memorize the value

Use of the control board

Figure 5.3 - Displays during advanced parameters programming

5. Press PROG. several times, until the displays return to normal

pressing times visualization.

The settings of the advanced parameters remain stored in the memo-

ry associated to the program in which they were entered.

For example: if the machine is running program number 5 and the

user enters advanced programming and excludes sleeve arms, the

sleeve arms will remain excluded for future use of program number

5, even after switching off the machine.

5.3. Pressing cycle counter meters

The machine is equipped with two cycle counters:

• Thetotalcountercountsallthepressingcyclescarriedoutby

the machine in its work life and cannot be reset.

• Thepartialcountercanberesetandcanbeutilized,forexam-

ple, to count the number of garments processed in one day.

Partial counter meter

• Toaccessthecounterspresspushbuttons and together

for two seconds.

• Theletter“C”appearsonthePROGdisplay.Theotherdisplays

show the number of cycles.

• Toresetthecounterpress“PROG”.

• Toexitmetermode,press

and together till the displays

STEAM, MIX, PAUSE, AIR show pressing times.

Total counter meter

• Toaccessthecounterspresspushbuttons and together

for two seconds.

• Theletter“C”appearsonthePROGdisplay.Theotherdisplays

show the number of cycles.

• Press+toviewthetotalcyclescountermeter.Thetotalcycles

counter cannot be reset.

• Toexitmetermode,press

and together till the displays

STEAM, MIX, PAUSE, AIR show pressing times.

The machine can work while the counter is visualized.

5.4. EXCLUSION section

This section consists of 4 buttons with red LED. The buttons allow

exclusion of the following functions:

• rearclampmovement

• frontclampmovement

• sleevearmsmovement

• collarclampmovement

Pushing the button relative to the function effects exclusion. When the

LED is on, the relative function is excluded.

Exclusions remain stored in the memory of the selected program.

Excludes the rear clamp. When the light is on the clamp does

not close. If the button is pushed during a cycle, the clamp

opens but the cycle continues.

Excludes the front clamp. When the light is on the clamp does

not close. If the button is pushed during a cycle, the clamp

opens but the cycle continues.

!2-3

Excludes the sleeve arms and cuff clamps. When the light is

on the sleeve arms do not operate. If the button is pushed

during a cycle, the cuff clamps open but the cycle continues.

#/,,!2

#,!-0

Excludes the collar clamp. When the light is on the collar clamp

does not operate. If the button is pushed during a cycle, the

collar clamp opens but the cycle continues.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 43 44

Comments to this Manuals

No comments

Electrolux FSF 650 Specifications Page 11

Comments to this Manuals

Related products and manuals for Ovens Electrolux FSF 650