Electrolux ESF4130 User Manual download pdf (Page 14)

Any electrical work required to install this appliance

should be carried out by a qualified electrician or

competent person.

Any plumbing work required to install this appliance

should be carried out by a qualified plumber or competent

person.

Remove all packaging before positioning the machine.

If possible, position the machine next to a water tap and a

drain.

Water supply connections

This dishwasher may be fed with either hot (max. 60°) or cold

water.

Nevertheless we advise you a cold water supply.

A hot water supply is not always efficient with very soiled

crockery as it shortens the washing programmes a lot.

The water pressure must be within the limits given in the

technical specifications.

Your local Water Authority will advise you on the average

mains pressure in your area.

The dishwasher features fill and drain hoses which can be

turned either to the left or the right to suit the installation.

The locknut must be correctly fitted to avoid water leaks.

Avoid bends or kinks in the hose which could prevent or slow

down the water supply.

If the machine is connected to new pipes or pipes which have

not been used for a long time, you should run the water for a

few minutes before connecting the inlet hose. This will prevent

deposits of sand or rust clogging the inlet hose filter.

For making the connection itself, the coupling nut fitted to the

machine’s supply hose is designed to screw onto either a 3/4

inch gas thread spout, or to a purpose made quick-coupling

tap such as the Press-block.

The water supply hose is fitted with a safety device, which

prevents water from entering the machine should the inner

hose split, due to wear.

Water outlet hose connection

The end of the drain hose can be connected in the following

ways:

1. To the sink outlet spigot, securing it if necessary with a clip.

2. Hooked over the edge of the sink using the special curved

plastic guide provided.

3. To a stand pipe provided with vent-hole, minimum internal

diameter 4 cm.

The waste connection must be at a height of between 30 cm

(minimum) and 100 cm (maximum) from the bottom of the

dishwasher.

The drain hose can face either to the right or left of the

dishwasher

Ensure the hose is not bent or squashed as this could prevent

or slow down the discharge of water.

If you use a drain hose extension it must be no longer than 2

metres and its internal diameter must be no smaller than the

diameter of the hose provided.

Likewise the internal diameter of the couplings used for

connections to the waste outlet must be no smaller than the

diameter of the hose provided.

The sink plug must not be in place when the machine is

draining as this could cause the water to siphon back into the

machine.

Attention!

Our appliances are supplied with a security device to

protect against the return of dirty water back into the

machine.

If the spigot of your sink has a "no return valve"

incorporated this can prevent the correct draining of your

dishwasher. We advise you therefore to remove it.

Electrical connection

Before plugging the appliance into the wall socket, make sure

that:

1. The mains voltage corresponds to the voltage given in the

"Technical specifications".

2. The meter, fuses, mains power supply and wall socket can

all take the maximum load required.

Make sure that the socket and plug are compatible without

having to use any type of adaptor. If necessary, have the

domestic wiring system socket replaced.

Safety standards require the appliance to be

earthed.

The manufacture accepts no liability for failure to observe

the above safety precautions.

Installation instructions

min 30 cm

max 100 cm

min 4 cm

CS09

max 100 cm

min 30 cm

max 100 cm

+ 2 m max

CS10

Ø 18

Ø 21

1 2 ... 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Electrolux ESF4130 User Manual Page 14

Comments to this Manuals

Related products and manuals for Dishwashers Electrolux ESF4130