Electrolux ENL60810X User Manual download pdf (Page 16)

16 electrolux side by side refrigeration user manual

If you purchased a refrigerator with a water lter (ice and water

models), please read the following care and use information.

An external water lter and connection kit has been supplied for

use with your ice & water refrigerator.

The external lter design allows more space within the refrigerator

and provides double the life of previous lters reducing the cost of

replacement. The lter is designed to signicantly reduce chlorine,

taste, odour, heavy metals, turbidity ( cloudiness) and scale

build up. The included plastic (LLDPE) water tube allows quick

connection to the lter and is designed for high durability and kink

resistance.

This lter is designed only to be used with a potable water supply.

It should not be used on water that is micro biologically unsafe or

with water of unknown quality. The lter should be replaced every

12 months. The service life of the lter may be reduced in water

supplies that contain an excess of particles or other impurities.

Reduced ow rate is an indication that a new lter is required.

Failure to replace the lter when required can affect the function of

the ice maker. Service calls caused by a failure to replace the lter

are not covered by warranty (see page 20).

When to change the ﬁlter

Water conditions vary throughout the world, but changing the

water lter every 12 months will ensure the highest possible water

quality. The electronics in your refrigerator will track the amount

of water usage and advise on when the lter should be replaced.

If the lter has not been in use for a while (because of a move for

example), change the lter before you reinstall the refrigerator.

Replacement lters can be purchased from the nearest Service

Centre (see page 20 for contact details). The lter change interval

can be reset by pressing the clock button.

Changing the ﬁlter

Turn off water supply at the tap. Ensure that the ice maker switch

is in the “O” (OFF) position.

To change the lter:

1. Turn off the water supply.

2. Release the pressure in the water lines by holding

a container against the water dispenser paddle on

the refrigerator until the pressure has been released.

3. Turn off the refrigerator at the power point and remove the plug

from the socket.

4. Depress the collet (see illustration below) and pull the tube out

of each end of the lter.

5. Ret the tubes into the new lter to the stops (about 15mm).

Ensure that you observe the ow direction.

Write the tment date in the space provided on the lter.

6. Gently pull back on the tube to ensure that it is secure.

7. Turn the water supply back on and check for leaks.

8. Plug the unit back in and turn the power supply back

on to the refrigerator.

9. Purge and dispose of approximately 5 litres of water through

the water dispenser to condition the lter and clear the

water lines of air and impurities. It may take up to a minute

to get a full ow of water from the dispenser. Do not be

alarmed if there is an initial black colour to the water.

This is residual carbon dust from the lter and is non-toxic.

10. Once the lines have been purged, dispose of the rst few

batches of ice to ensure that impurities have been ﬂushed from

this part of the system.

External water filter – installed

between fridge and water supply.

(Usually situated within kitchen

cupboard under sink or surrounds).

Tube supplied with

filter installation kit.

Cut to fit as per your

kitchen requirements.

From water supply

Flow directionTo fridge

Collet (blue ring).

There is a collet

at both ends.

Changing the water lter

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 83 84

Comments to this Manuals

No comments

Electrolux ENL60810X User Manual Page 16

Comments to this Manuals

Related products and manuals for Fridges Electrolux ENL60810X