Electrolux ER2620C User Manual download pdf (Page 7)

Defrosting

The refrigerator automatically defrosts every time the

compressor stops. The water is discharged, via the

pipe, into a tray located at the back of the appliance

above the compressor, where it evaporates.

Important

To avoid defrost water overflowing into the fridge,

periodically clean the water discharge hole in the centre

of the V shaped drip collector at the back of the

refrigerator compartment behind the fruit and vegetable

drawer. Use the defrost cleaner provided which you will

find already inserted into the discharge hole.

Remember to wash the defrost cleaner in hot soapy

water at regular intervals. Dry throughly before

replacing.

D037

MAINTENANCE AND CLEANING

External cleaning

Wash the outer cabinet with warm soapy water. Do

NOT use abrasive products.

An accumulation of dust will affect the performance

of the appliance and cause excessive electricity

consumption.

You MUST ensure that the appliance is switched

OFF.

Once or twice a year dust the condenser (black grill)

and the compressor at the back of the appliance,

with a brush or vacuum cleaner, see diagram.

D273

CONDENSER

COMPRESSOR

DEFROST

TRAY

Before any maintenance or cleaning work is carried

out, DISCONNECT the appliance from the

ELECTRICITY supply.

Internal cleaning

Clean the inside and accessories with warm water

and bicarbonate of soda (5ml to 0.5 litre of water).

Rinse and dry thoroughly.

NEVER USE DETERGENTS, ABRASIVE

POWDERS, HIGHLY PERFUMED CLEANING

PRODUCTS OR WAX POLISHES, TO CLEAN

THE INTERIOR AS THESE WILL DAMAGE THE

SURFACE AND LEAVE A STRONG ODOUR.

Clean the drain hole of the water trough at regular

intervals and make sure that the drain hole is never

obstructed, so that the defrost water may flow freely.

Changing the light bulb

Should the interior light fail to work, first switch off

the appliance and disconnect from the electricity

supply, then replace the bulb as follows;

Unscrew the light cover and then pull it outward by

pressing as shown in the figure. Unscrew the bulb

and replace it with a new 15 watt bulb (available

from your nearest Electrolux Service Force Centre).

Replace the light cover by sliding it into its original

position and replacing the screw.

D411

When the appliance is not in use

When the appliance is not in use for long periods,

disconnect from the electricity supply, empty all

foods and clean the appliance, leaving the doors ajar

to prevent unpleasant smells.

INSTALLATION

Positioning

This appliance is designed to operate in ambient

temperatures between 10¡C (50¡F) and 32¡C (90¡F).

It should be located in a dry atmosphere, out of

direct sunlight and away from extreme temperature

e.g. not next to a boiler or radiator, or in a very cold

room e.g. an outhouse, where the temperatures may

fall below 10¡C (50¡F). If these temperatures are

exceeded i.e. colder or warmer, then the appliance

may not operate correctly.

You should also ensure that air can circulate freely

around the back and the top of the cabinet. There

must also be at least 100 mm (4Ó) distance between

the top of the cabinet and any overhanging kitchen

furniture (A). Ideally, the appliance should not be

positioned beneath overhanging furniture (B).

There should also be a gap of 25 mm either side of

the appliance. Do not obstruct the space

underneath. The back of the cabinet may be placed

close to the wall but must not touch it. DO NOT

install in places with restricted ventilation.

Adjust the level of the appliance by screwing out the

adjustable foot, or feet, at the bottom of the cabinet

using your fingers or a spanner (see figure).

D200

100 mm10 mm

10 mm

NP007

Warning

IF YOU ARE DISCARDING AN OLD APPLIANCE

THAT HAS A LOCK OR CATCH ON THE DOOR,

YOU MUST ENSURE THAT IT IS MADE

UNUSABLE TO PREVENT YOUNG CHILDREN

BEING TRAPPED INSIDE.

Depending upon the position which you choose for

your appliance, you may wish to reverse the way in

which the door opens. To do this, refer to instructions

on ÒDoor reversal directionsÓ.

Important

It must be possible to disconnect the appliance from

the mains power supply; the plug must therefore be

easily accessible after installation.

Rear spacers

The plastic bag containing all relevant

documentation also contains two spacers to be fitted

into special holes in the back of the appliance.

Fit the spacers into the holes, taking care to ensure

that the arrow (A) is positioned as shown in the

diagram. Then turn them through 45¡ (arrow (A)

vertical) until they lock into place.

PR60

45°

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Electrolux ER2620C User Manual Page 7

Comments to this Manuals

Related products and manuals for Fridges Electrolux ER2620C