Electrolux SBB800S-1 Installation Manual download pdf (Page 37)

(1) Open a hot water xture and conrm that the Burner On lamp comes on, and that hot water is

being produced. (If necessary, repeat until the air in the gas piping is bled out).

* White smoke may be noticed from the exhaust vent during cold weather. However, this is not

a malfunction of the unit.

If an “11” error code appears on the remote controller, turn the unit off and then back on again,

and then open a hot water xture again.

(2) Change the temperature setting on the remote controller and check that the water temperature changes.

r

If the water heater does not operate normally, refer to “Troubleshooting” in the Use and Care Manual.

* After the trial operation, clean the lter in the cold water inlet.

r5VSOUIFTZTUFNQPXFS0/XJUIUIFSFNPUFDPOUSPMMFS

r4MPXMZPQFOBIPUXBUFSàYUVSFBOEDIFDLUIBUUIFVOJUTJHOJUFTFRVFOUJBMMZ$IFDLUPTFFUIBUUIF

hot water temperature is the same as the temperature displayed on the remote controller. (*1)

* If both units do not ignite, switch which unit will ignite rst by pressing the Max. or Min. Mani-fold

Pressure Set Button on the circuit board. (*2)

* If an 11 or F11 error code ashes on the remote controller, hit the Power Button on the remote

controller off and on 2 -3 times.

* If (*1) and (*2) cannot be done, the Quick Connect Cord may not be properly connected.

Check that the cord is properly connected.

14.

Maintenance

Periodically check the following to ensure proper

operation of the water heater.

r5IFWFOUJOHTZTUFNNVTUCFFYBNJOFEQFSJPEJDBMMZCZBRVBMJàFETFSWJDFUFDIOJDJBOUPDIFDLGPS

any leaks or corrosion.

r5IFCVSOFSáBNFNVTUCFDIFDLFEQFSJPEJDBMMZGPSBQSPQFSCMVFDPMPSBOEDPOTJTUFODZ

r*GUIFáBNFEPFTOPUBQQFBSOPSNBMUIFCVSOFSNBZOFFEUPCFDMFBOFE

r*GUIFCVSOFSOFFETUPCFDMFBOFEJUNVTUCFQFSGPSNFECZBRVBMJàFETFSWJDFUFDIOJDJBO

r%POPUPCTUSVDUUIFáPXPGDPNCVTUJPOBOEWFOUJMBUJPOBJS

r5IFQSFTTVSFSFMJFGWBMWFNVTUCFPQFSBUFEPODFBZFBSUPFOTVSFUIBUJUJTGVODUJPOJOHQSPQFSMZBOE

there is no obstruction. Turn the power off to the unit before opening the relief valve, and make

sure that water draining out of the valve will not cause any damage.

r

If the relief valve discharges periodically, it may be due to thermal expansion in a closed water system.

Contact the water supplier or a local plumbing inspector on how to correct this situation.

Do not plug the relief valve.

r4FF6TFBOE$BSF.BOVBMGPSGVSUIFSNBJOUFOBODF

Warning:

There is a scald potential if the output temperature is set too high.

Should overheating occur, or the gas supply fail to shut off, turn off the manual gas control valve to the appliance.

Do not use this appliance if any part has been under water. Immediately call a qualied service technician

to inspect the appliance and to replace any part of the control system and any gas control which has

been under water.

Periodically check and clean the lter inside the cold water inlet of the unit.

15.

Trial Operation

The installer should test operate the unit, explain to

the customer how to use the unit, and give the owner

this manual before leaving the installation.

Unit A Ignites

Unit B Doesn't Ignite

Press Max. or Min. Manifold

Pressure Set Button on Unit B

Unit A Doesn't Ignite

Unit B Ignites

r 1SFQBSBUJPO 0QFOBIPUXBUFSàYUVSFUPDPOàSNUIBUXBUFSJTBWBJMBCMFBOEUIFODMPTF

the xture.

(2) Open the gas supply valve.

(3) Turn on the power supply. Using the remote controller, turn on the Power

On/Off button (the Operation lamp will turn on).

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 83 84

Comments to this Manuals

No comments

Electrolux SBB800S-1 Installation Manual Page 37

Comments to this Manuals

Related products and manuals for Water heaters & boilers Electrolux SBB800S-1