SERVICE MANUAL VACUUM CLEANER © E.H.P. Floor Care Number of publication 599 71 19-22
Display cover Detach the side cover using a fine-tipped screwdriver Detach the side cover using a fine-tipped screwdriver Lift up the display cover Re
Detach from the outside the power button using a fine-tipped screwdriver Remove the springs from the buttons Detach from the inside the power button u
PCB Display/Switch Detach the pressostat hose Remove the PCB with the reflector on it Detach the PCB supply cable Detach the reflector tab from the bo
Top cover Remove the screws that fix the top cover Detach the top cover using a fine-tipped screwdriver Detach the top cover using a fine-tipped screw
Remove completely the top cover from the back Remove completely the top cover from the front EN Publication number 599 71 19-22 Rev. 01 02/2009 PR -
Housing Remove the seven screws that fix the housing of the cleaner Remove the gasket from its site Remove the filter from the holder Remove complete
Detach the pressostat hose Lift up the cord winder cover Remove the screw from the cord winder cover Remove the screws that keep the cord winder assy
Remove completely the cord winder EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 17/42
Handle Detach the left handle cover using a fine-tipped screwdriver Detach the right handle cover using a fine-tipped screwdriver Remove completely th
Detach the internal rubber part of the handle using a fine-tipped screwdriver Detach the internal rubber part of the handle using a fine-tipped screwd
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 2/42 TABLE OF CONTENTS 1 General description ...
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 20/42 Remove completely the axe from the wheel Detach the wheel covers using a fine-tipped
Remove the screws that fix the metal plate to the structure EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 21/42
Detach the connection Detach the connectors using a fine-tipped screwdriver Detach the connection Detach the pressostat hose Detach the connectors usi
Remove completely the motor Detach the pressostat hose Remove the screws that keep joined the two housing Remove the screws that keep joined the two h
Remove the absorber outer filter Remove the motor’s cover EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 24/42
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 25/42 HBTN Nozzle Telescope tube Bent end Remove the screw using a torx screwdriver Detac
Detach the lever from the cover Detach the wheel cover using a fine-tipped screwdriver Remove 2 screws using a fine-cross screwdriver Remove the scre
Detach the cover from the hose Detach the remote control using a fine-tipped screwdriver Detach the cover using a fine-tipped screwdriver EN Publicat
3 Levels of Electronic Control 3.1 Display Layout for models without remote controlled HBTN: 3.1.1 Basic software functionality - ON/OFF switch
3.2 Display Layout for models with RF controlled HBTN: 3.2.1 Basic software functionality - ON/OFF switch - Soft-start - Automatic 50/60Hz dete
1 General description 1 Display 2 Hepa filter cover 3 Hepa filter 4 Parking slot 5 Power cord 6 Motor filte
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 30/42 - Motor turns off; last power setting and mode is remembered by the microcontroller
3.3 Display Layout for models with Aeropro active system: 3.3.1 Basic Software functionality - ON/OFF switch - Soft-start - Automatic 50/60Hz de
3.4 Nozzle power supply interface For vacuum cleaners with AUTO mode function: 4 button 1 turns on or off the cleaner button 2 turns on or off th
- Keep the ON/OFF button pressed until the AUTO LED:s start flashing, the cleaner is now in RF learning mode. Release the ON/OFF button. - On the re
3.7 Auto function, pressure sensor PCB (position 014D) Auto function is a function for automatically regulate the motor power depending on the air
4 PCB Power Module (position 014A) 4.1 Introduction Power module is intended as a module PCB for mainly vacuum cleaners from Electrolux Floor Care
4.3 Low Current Power Module The low current power module contains a capacitive power supply. The low current power module can always be replaced by
5 RF transmitter 5.1 Introduction The RF transmitter is used as remote control for a vacuum cleaner powered by a 3V changeable lithium cell. The t
6 Aeropro PCB 230V/110V motor 6.1 Introduction Aeropro PCB 230V is a new PCB to support the drive of a 230VAC motor mounted in the Aeropro nozzle.
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 39/42 6.3.1 Functional description The Aeropro PCB is supplied with main voltage, dimens
1.1 Exploded view EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 4/42
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 40/42 7.1.2 Deactivation To deactivate the LED indicator after activation this can be ma
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 41/42 8 TROUBLE SHOOTING Problem Checks Cleaner without remote: - Investigate if the plas
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 42/42 Cleaner with radio remote: - Investigate if the LED on the remote indicates transmis
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 5/42 Pos Description Pos Description Pos Description 1 BASE 23 HOSE CONNECTION INNER
EN Publication number 599 71 19-22 Rev. 01 02/2009 PR - 6/42 2 ACCESSIBILITY The following chapter follows a disassembling process that step by
Dust bag cover and compartment Open the dust bag cover Lift up the lock cover of the lid Remove the Hepa filter Press the lock covers Completely det
Release the left anchor Release the right anchor of the dust bag cover Carefully detach this part Detach the lock using a fine-tipped screwdriver Remo
Release the right anchor of the lid accessory Remove the spring from the dust bag cover Release the anchor and remove the lid accessory EN Publication
Comments to this Manuals