Electrolux ER7926B User Manual download pdf (Page 5)

OPERATION

Before using

Remove all securing tapes. Wash inside the

appliance with lukewarm water and bicarbonate of

soda (5 ml to 0.5 litre of water).

Do not use soap or detergent as the smell may

linger. Dry thoroughly.

Setting the temperature

The temperature inside the appliance is regulated by

a thermostat with 6 temperature positions and an

“OFF” (O) position.

Position 1 = minimum coldness

Position 6 = maximum coldness

Turn the thermostat dial to the required position.

The intermediate position is usually the most

suitable (3-4).

The thermostat control regulates the temperature

both within the fridge and the freezer compartment.

The thermostat setting can vary as the temperature

inside the appliance depends on the following

factors:

– room temperature

– how often the door is opened

– how much food is stored

– position of the appliance

Fresh food refrigeration

To obtain the best performance, do not store warm

food or evaporating liquids in the refrigerator; cover

or wrap the food, particularly if it has a strong flavour.

Do not cover the shelves with any protective

material, such as paper, cardboard or plastic, which

may obstruct the air circulation.

To help you use your refrigerator correctly, here are

some more useful hints:

Raw meat (beef, pork, lamb & wild fowl): wrap in

polythene bags and place on the glass shelf above

the salad drawers.

Meat can only be stored safely in this way for

one or two days at the most.

Fruit & vegetables: these should be thoroughly

cleaned and placed in the salad drawers.

Butter & cheese: these should be placed in special

airtight containers or wrapped in aluminium foil or

polythene bags to exclude as much air as possible.

Milk bottles: these should have a cap and should be

stored in the bottle rack on the door.

To Start the Appliance

Allow the appliance to stand for 2 hours after

installation.

Plug in the appliance and switch on at the mains

supply. Open the fridge door. Turn the thermostat

control to a midway setting (3-4) and adjust the slider

control, situated on the back wall of the fridge

section, to a midway position between “MIN” and

“MAX”. Leave the appliance for approximately 4

hours for the correct temperature to be reached

before placing food inside.

To switch off the appliance turn the thermostat

control to position “O”

Use of an air circulation slider

control - COOL FLOW CONTROL

Your appliance has an air circulation slider control

situated at the rear of the fridge compartment, which

controls the amount of cold air circulated through the

fridge compartment.

When the ambient temperature is between 10°C and

16°C, the slider control should be in the “MIN”

position.

When the ambient temperature is above 16°C the

slider control should be midway between “MIN” and

“MAX”.

When the ambient temperature is very high (i.e. hot

summer days) position the slider control to “MAX”.

D757/1

MIN

MAX

COOL FLOW CONTROL

MIN MAX

COOL FLOW CONTROL

Electrical connections

Any electrical work required to install this appliance

should be carried out by a qualified electrician or

competent person.

WARNING: THIS APPLIANCE MUST BE

EARTHED.

The manufacturer declines any liability should

this safety measure not be observed.

If the plug that is fitted to your appliance is not

suitable for your socket outlet, it must be cut off and

the appropriate plug fitted.

Remove the fuse from the cut off plug.

The cut off plug should then be disposed of to

prevent the hazard of shocks in case it should be

plugged into a 13amp socket in another part of your

home.

Important

The wires in the mains lead are coloured in

accordance with the following code:

Green and Yellow - Earth

Blue - Neutral

Brown - Live

If you fit your own plug, the colours of the wires in

the mains lead of your appliance may not

correspond with the markings identifying the

terminals in your plug, proceed as follows:

Connect the Green and Yellow (earth) wire to the

terminal in the plug which is marked with the letter

«E» or the earth symbol or coloured green and

yellow.

Connect the blue (neutral) wire to the terminal in the

plug which is marked with the letter «N» or coloured

black.

Connect the brown (live) wire to the terminal in the

plug which is marked with the letter «L» or coloured

red.

The plug moulded onto the lead incorporates a fuse.

D207

GREEN & YELLOW

13 AMP. FUSE

BROWN

CORD CLAMP

BLUE

13 AMP

For replacement, use a 13amp BSI362 fuse. Only

ASTA or BSI approved fuses should be used.

The plug must not be used if the fuse cover/carrier is

lost. The cover/carrier is indicated by the coloured

insert at the base of the plug.

A replacement cover/carrier must be obtained from

your local Electrolux Service Force.

This appliance complies with the E.E.C. Directive

No. 87/308 of 2.6.87 relative to radio interference

suppression.

This appliance complies with the following

E.E.C. Directives:

- 73/23 EEC of 19.2.73 (Low Voltage Directive)

and subsequent modifications;

- 89/336 EEC of 3.5.89 (Electromagnetic

Compatibility Directive) and subsequent

modifications.

Please ensure that when the appliance is

installed it is easily accessible for the engineer in

the event of a breakdown.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Electrolux ER7926B User Manual Page 5

Comments to this Manuals

Related products and manuals for Fridges Electrolux ER7926B